Ecobee Screen Wont Turn On

RobotPoweredHome is reader-supported. When you buy through links on my blog, I may earn an affiliate committee. Every bit an Amazon Acquaintance, I earn from qualifying purchases.

Are you facing issues with your Ecobee Thermostat? Yous must be probably looking at your blank Ecobee thermostat screen and freaking out.

You attempt pressing the buttons, but in that location's no response. Don't freak out yet. There are a good number of reasons why the power might have gone out.

I can assistance you out considering I went through the same ordeal a few months ago.

Depending on whether you lot accept merely installed your thermostat or working fine before, you lot may need to endeavour different methods to set up your thermostat.

Inspect the Breaker and Heater Power Switch
Check If The Heater Overheated and Tripped
Examine the Furnace Fuse
Check The Air Conditioner For Condensate Drippage

This guide volition help you lot await at each of these fixes to get your Ecobee Thermostat working.

Audit the Breaker and Heater Power Switch

If your dwelling or locality has experienced a ability surge recently, or if you have experienced a lightning storm, and so your breaker switch may have flipped.

Often, the breaker switch flips considering of excessive ability drawn. It is completely fine to flip the switch back and plough on your Ecobee Thermostat in most cases.

However, if you find that this problem occurs often, it could be an indication of faulty wiring.

Here is how you can safely inspect the breaker switch:

Head to your breaker box and check whether the switch powering your thermostat is off.
Flip it back on and wait for at least 30 seconds to ensure that it does non turn off automatically.
Await for some time and allow your thermostat to plough dorsum on.
Arrange the ability settings to ensure that your thermostat is operation correctly.
In case the thermostat turns off afterwards you have adjusted the temperature settings, information technology could signal issues with your Ecobee Thermostat; contact a technician or Ecobee back up to ensure to fix the thermostat correctly.

Bank check If The Heater Overheated and Tripped

Did you attempt to increase the heating power and your car turned off? Every heater has an in-built sensor that trips and turns the system off in case information technology gets overheated.

The fan may continue to run to help absurd the system off, or the organization may not function at all until it is cooled off.

A heater can overheat in the post-obit situations:

Colder Temperatures Exterior: When information technology is colder outside, you will likely take your heater running for a long fourth dimension. The heater will need to work harder at increased temperatures and more extended periods to keep your home warm. In some cases, this may cause the heater to get overheated. Hence, information technology is all-time to give your heater a little suspension from fourth dimension to time during colder days.
Chock-full Filters or Build-up of clay: Your air filters need to be cleaned from fourth dimension to time to ensure that it is non clogged up. When the filters are clogged, the heater will need to work harder to ensure heat to the house. In case your filter has been cleaned recently, then you should bank check other parts of the car for a build-up of dust likewise.

Examine the Furnace Fuse

The Ecobee furnaces system itself should take a fuse to assistance protect it from power surges.

To check the fuse, locate and open the furnace panel. When the fuse torso is clear, bank check the wire within.

If broken, and then the fuse is blown. In instance the body has turned black, it indicates a blown-out fuse as well.

When checking the furnace fuse, ensure to plow off the system completely to forbid electrical shocks.

A commonly used fuse for furnaces is a 3 Amp imperial body fuse or a five Amp orange body fuse.

You can replace these components if damaged. Keep in mind that they are not interchangeable.

If your organisation uses a 3 Amp fuse, you cannot replace it with a 5 Amp ane. The rating is not an indication of the fuse's operation. Instead, information technology is selected explicitly for the system and its excursion.

Cheque The Air Conditioner For Condensate Drippage

Excessive h2o build-upward due to condensation is a common reason why Ecobee Thermostat frequently does not turn on.

If the water exceeds a specific level, the system sensors volition plough off the machine for safe.

All systems come with a drainage organization or a baste pan. Depending on the model you lot utilize, you can locate it above the machine or outside.

Aggregating of h2o in the system may lead to mold growth, algae or it may clog upwards the pipe due to accumulation of droppings.

Signs of water accumulation in the organization

Puddles, water leakage, dripping, and moisture near your system or on it.
Your condensate drain pan is overflowing or becoming tiresome.
Your machine is rebooting frequently or not turning on.
Evidence of h2o harm near or on your condensate drain pan or drainage line.

How to fix this issue

Locate the evaporator coils, condensate bleed pan, and drainage pipe. Depending on the model you utilize, the evaporator coils and drain pan may be located above or below the system. Sometimes, you tin find the drain pan beside the system, and information technology unremarkably has a PVC drainage pipe attached to it.
Check whether the drain pan is full. In instance it is, drain the pan and clean it carefully.
Check for clogs within the drainage pipe. While some DIY methods to make clean the drain pipe are easy to follow, you can also hire ta HVAC technician for this.
Locate the float switch; you can discover it side by side to the drain pan located at the system's bottom. When the water or condensation exceeds a specific level, the bladder switch trips and turns the arrangement off. After you take successfully tuckered the water and cleaned the drainage pipe, you can turn on the float switch without whatsoever issues.

Unable to find the bladder switch? Open your device'due south prophylactic panel and bank check the prophylactic devices.

Normally, you lot'll see the prophylactic device connected to the "R" terminal. Follow the wire, and y'all will be able to locate the float switch.

Yet Unable to Prepare Your Ecobee Thermostat's Bare Screen? Troubleshooting Tips

In case y'all accept simply installed your Ecobee thermostat, the chances are that the to a higher place tips won't work out for yous.

Commonly, when it comes to a newly installed Ecobee, the trouble lies with the wire and connections of the Ecobee.

Here is what you can exercise:

Check the Power Wire: The Ecobee needs to be connected to the wire source properly. Ensure that the power wire is continued to the R terminal securely. Cheque the other connections past gently pulling the wires to confirm they are secure.
Performance C Wire: Your Ecobee should come with extra C wires, so you tin easily replace them if they aren't working. If the C wire is not connected, ensure to do so deeply.
Power Extender Kit: If you lot have the Ecobee3 or Ecobee4 model, check that the wiring is fastened correctly: Connect the R wire to the R terminal, the K wire to the C final, the W wire to the W1 terminal, and the Y wire to the PEK last.

If no method seems to be working for you, or if your system keeps rebooting frequently, information technology may signal a trouble with your system.

In this case, ensure that y'all telephone call a professional technician to keep the event from worsening.

Conclusion:

The Ecobee Thermostat non turning on is stressful and frustrating, especially when the weather condition is less than ideal.

When waiting for a technician to stop by isn't an option, some DIY options tin exist quite useful.

Some common problems, such equally a tripped breaker switch, the device overheating, or a tripped float switch, are easy to set.

Post-obit the simple methods that I have listed above can assistance yous get your thermostat up and running in no fourth dimension.

I've curated this list carefully to ensure that you tin can find a quick set up for your device using a safe method that won't impairment your device.

You May Also Savor Reading

My Ecobee Says "Calibrating": How To Troubleshoot [2021]
5 Honeywell Wi-Fi Thermostat Connection Problem Fixes
Does Nest Thermostat Piece of work With HomeKit? How To Connect
Nest Thermostat 4th Generation: The Smart Home Essential

Frequently Asked Questions

How do you lot wake upward Ecobee?

Your personalized Comfort setting informs the Ecobee which part it should perform at specific times. When you lot want to wake your Ecobee upwards, you need to:

Select the Bill of fare selection on the thermostat and and then select Schedule.
Select the 24-hour interval you wish to adjust, and then tap on the action you want to modify.
Select your desired starting time time and save.

In case yous want to beginning a new activity:

On the schedule page, tap on the '+' icon.
Select your desired Comfort setting.
Add the desired start fourth dimension and click on relieve.

How practise I get my Ecobee back online?

Connect your Ecobee to your Wi-Fi with the post-obit steps:

Tap on the carte pick on your thermostat.
Click on the Settings selection and and then select the Wi-Fi choice. This volition open the Wi-Fi configuration carte.
Ensure that the Wi-Fi Radio option is enabled, and and so select the Network option.
On the screen, y'all will take the option to cull betwixt setting upwards an iOS device or manually configuring a Wi-Fi network. Select the Wi-Fi option if you lot exercise non accept an iOS device
In one case you opt for the "Select Wi-Fi Network" option, you will find a list of the available Wi-Fi networks.
Tap on your Wi-Fi network and enter your countersign.
Select the Connect option and expect until the Ecobee connects successfully.
Once connected, it volition show a success message on the screen. Tap on OK to proceed.

Notation: If you have a dual-band network and want to connect an Ecobee3, Ecobee3 Lite, or Ecobee4 model, ensure that you lot select the 2.iv GHz option from the listing.

How do I set my Ecobee sensor?

Your sensor may non be working due to low battery or improper pairing.

To replace the battery:

Gently remove the battery encompass.
Take the old battery out and replace it with a 3-volt CR-2032 battery.
Ensure that the '+' signs are facing upwardly when placing the battery inside the sensor.

To re-pair the sensor:

Have the battery out and so identify it back in with the '+' facing downward.
After two minutes, take the battery out and insert information technology with the '+' facing up.
Afterwards a few seconds, a bulletin prompting you to pair the sensor should announced on your thermostat. Follow the steps to reconnect your sensor.

What happens if Ecobee loses the Wi-Fi connection?

The Ecobee Thermostat will continue to function as a regular thermostat if it loses Wi-Fi connexion.

It will continue to regulate the internal temperature according to the set temperatures.

Merely y'all volition non be able to remotely adjust its settings until the Ecobee connects to the Wi-Fi again.

Source: https://robotpoweredhome.com/ecobee-thermostat-blank-black-screen/